Oil consumption realities

Tips and Recommendations from Guru Mike Nixon

Moderator: Whiskerfish

Post Reply
User avatar
rcmatt007
Treasurer
Treasurer
Posts: 31305
Joined: Fri Oct 21, 2005 12:48 pm
My Album: http://www.ngwclub.com/gallery/v/wingmans/rcmatt007/
Location: New River Valley, Virginia

Re: Oil consumption realities

#16

Post by rcmatt007 »

my favorite pastime is to pour a little oil under a parked GL1800 :twisted:
User avatar
Sidecar Bob
Honored Life Member
Honored Life Member
Posts: 7633
Joined: Sun Jun 11, 2006 10:14 pm
Location: Kawartha Lakes, Ontario

Re: Oil consumption realities

#17

Post by Sidecar Bob »

Many years ago someone pointed out a puddle under a friend's sidecar outfit as a possible oil leak. It was under the front of the sidecar so he didn't worry until he saw a similar puddle at the next stop. Turned out the cap had come off of the bottle of oil he kept behind the seat with the tools, a tool had punctured the seal and it was running under the floor mat (where his passenger didn't see it) and out a drain hole.
User avatar
mikenixon
Early 'Wing Guru
Early 'Wing Guru
Posts: 997
Joined: Thu Dec 10, 2009 1:51 am
Location: Prescott, AZ
Contact:

Re: Oil consumption realities

#18

Post by mikenixon »

:)
PDub
Cast Iron Member
Cast Iron Member
Posts: 67
Joined: Fri Sep 16, 2011 3:55 pm
Location: Annapolis, MD

Re: Oil consumption realities

#19

Post by PDub »

Late to this topic but there is a show on TV called Engine Masters. They basically dyno test different engine ideas that are either controversial or thought to be common knowledge to determine what is actually true.

They recently went through a test of oil pans and picked up significant horsepower with just the change of the oil pan. This pan was specifically designed to allow the oil to get channeled away and reduce interference with the spinning crank. This reduced drag on the crank since it wasn't spinning in a cyclone of oil and therefore power increased. Oil pressure also improved due to less foaming action. They actually found power highest when the pan was a quart low! Obviously, they didn't recommend this for a street engine, but it does point to Mike's premise about oil vaporization.

Good read as always Mike. Thanks!
User avatar
mikenixon
Early 'Wing Guru
Early 'Wing Guru
Posts: 997
Joined: Thu Dec 10, 2009 1:51 am
Location: Prescott, AZ
Contact:

Re: Oil consumption realities

#20

Post by mikenixon »

Speaking of unusual engines and particularly oil pans, when Kawasaki put a ZX1200 Ninja sportbike engine in their first four-stroke personal watercraft they of course didn't include the transmission so the crankcases are quite different. The crankcases wrap closely around the crankshaft, still in a wet sump design though, and special baffling and oil channeling is added so when the craft tips 90 degrees or even farther the oil pump won't starve for oil and when righting the craft there is no delay in lubrication. There is also a air/oil separator plumbed in. Interesting what engineers come up with. And since the basic engine is Ninja-derived comparisons are easy to make and the differences obvious and instructive. By the way, speaking of skimming the oil film off a spinning crankshaft, Honda was using crankshaft "windage trays" as early as the early 1960s twins. On the CB450 DOHC bikes the tray is part of the crankcase, permanently riveted in.
User avatar
gltriker
Honored Life Member
Honored Life Member
Posts: 5053
Joined: Fri Sep 24, 2010 9:11 pm
Location: central NY State

Re: Oil consumption realities

#21

Post by gltriker »

PDub wrote: Fri Mar 12, 2021 3:45 pm Late to this topic but there is a show on TV called Engine Masters. They basically dyno test different engine ideas that are either controversial or thought to be common knowledge to determine what is actually true.

They recently went through a test of oil pans and picked up significant horsepower with just the change of the oil pan. This pan was specifically designed to allow the oil to get channeled away and reduce interference with the spinning crank. This reduced drag on the crank since it wasn't spinning in a cyclone of oil and therefore power increased. Oil pressure also improved due to less foaming action. They actually found power highest when the pan was a quart low! Obviously, they didn't recommend this for a street engine, but it does point to Mike's premise about oil vaporization.

Good read as always Mike. Thanks!
I have seen that same Engine Masters episode several times .
In fact, it will replay again at 8:30pm, tonight.
Shadowjack
Silver Member
Silver Member
Posts: 654
Joined: Fri May 26, 2017 11:07 am

Re: Oil consumption realities

#22

Post by Shadowjack »

The CB72/77 twins also have the windage trays in the sump, IIRC. Muscle-car era Pontiac performance engines have them as well from the factory. Probably others, but those I know.
User avatar
flyin900
Gold Member
Gold Member
Posts: 1489
Joined: Sun Jan 10, 2010 3:50 pm
Location: Canada

Re: Oil consumption realities

#23

Post by flyin900 »

Windage trays.....

Just helping a buddy with a 1968 CL175 Twin where we needed to spit the cases to replace a worn/damaged kick starter shaft assembly.
Since the motor was a last fall take apart project and then left for 3 months; this motor has two small windage trays on either side of the front section of the lower case. These were placed elsewhere during those three months, so we ended up reassembling the replaced kick assembly and rejoining the upper and lower cases.
Only when checking the parts fiche for a bolt washer confirmation did we discover the "windage trays" were shown on the fiche and we realized that they were missing from the lower case. :IDTS:
User avatar
77Gowing
True Blue Steel Biker
True Blue Steel Biker
Posts: 2724
Joined: Wed Jul 22, 2015 4:31 pm
Location: San Angelo, Texas

Re: Oil consumption realities

#24

Post by 77Gowing »

The Teledyne Continental engine in the M60 tank and the Army's tank retriever, is 1790 cid and has what they call a dry sump. There is no vessel beneath the pick up tubes. I was told that this arrrangemnment would allow extreme angles on the engine. I can see where it would help on the specified 60% grades.

When it comes to oil trays...I'm completely....baffled!8 :lol:
User avatar
mikenixon
Early 'Wing Guru
Early 'Wing Guru
Posts: 997
Joined: Thu Dec 10, 2009 1:51 am
Location: Prescott, AZ
Contact:

Re: Oil consumption realities

#25

Post by mikenixon »

:)
User avatar
mikenixon
Early 'Wing Guru
Early 'Wing Guru
Posts: 997
Joined: Thu Dec 10, 2009 1:51 am
Location: Prescott, AZ
Contact:

Re: Oil consumption realities

#26

Post by mikenixon »

flyin900 wrote: Sat Mar 13, 2021 10:18 am Windage trays.....

Just helping a buddy with a 1968 CL175 Twin where we needed to spit the cases to replace a worn/damaged kick starter shaft assembly.
Since the motor was a last fall take apart project and then left for 3 months; this motor has two small windage trays on either side of the front section of the lower case. These were placed elsewhere during those three months, so we ended up reassembling the replaced kick assembly and rejoining the upper and lower cases.
Only when checking the parts fiche for a bolt washer confirmation did we discover the "windage trays" were shown on the fiche and we realized that they were missing from the lower case. :IDTS:
On the DOHC CB450 twin the trays have Phillips screws holding them in, plus rivets that have to be cut using a special tool. You can't really flush out all the sludge with them in place. But you can put the trays back in upside-down... :8)
Post Reply
  • Similar Topics
    Replies
    Views
    Last post

Return to “Mike Nixon's Spot”