1985 GL1200 Limited, time for a new project.

[bigscheaf]

That would be awesome! And no worries, I’m not a programmer by day either, but I can be dangerous.

I’ll have to dig on cb1100f.net and see if I can find the other post. Might be able to share some additional insight from the inline 4 side of the house. Should be fairly similar between the two platforms for the speedometer and tachometer.

there are 330 lines of code, if you PM me your email address I will send it to you.

Sounds pretty workable for what is being accomplished with the Arduino. And tweaking things like this are right up my alley. PM on the way.

[Wolfie666]

C5 Ignition is meant for the left cylinder head, but my FI engine has it on the right, so a little machining to the OEM housing to use for backplate...

20150618_183816.jpg (103.18 KiB) Viewed 512 times

20150619_070521.jpg (85.77 KiB) Viewed 512 times

20150619_073133.jpg (93.05 KiB) Viewed 512 times

20150619_073151.jpg (83.87 KiB) Viewed 512 times

20150619_193928.jpg (102.23 KiB) Viewed 512 times

[Wolfie666]

Mounted...

2019-04-06 16.25.58.jpg (1.06 MiB) Viewed 511 times

2019-04-06 16.26.02.jpg (1.07 MiB) Viewed 511 times

Also made and mounted a 40A Circuit Breaker...

2019-04-06 16.09.56-2.jpg (1.02 MiB) Viewed 511 times

2019-04-06 16.10.04.jpg (1013.42 KiB) Viewed 511 times

[Rednaxs60]

That is one good use for the old Gr/Gl cam (PG) sensor placement from the CFI system. Ready made and don't have to do too much work to use. Nice job.

[Easter]

My ten gallon hat is off to you!

[Wolfie666]

Wiring the Denso Coils...

2019-04-13 17.41.46.jpg (1.02 MiB) Viewed 453 times

[Rednaxs60]

Good COP install. Can you provide more info on the COP units you selected?

[Wolfie666]

Good COP install. Can you provide more info on the COP units you selected?

Sure,
2003 - 2006 Honda CBR600RR

Can get them on Ebay fairly inexpensive, and the harness usually comes with it,
but I prefer to make my own instead of cutting and splicing.
The connectors can be found there as well by searching for...
6 PACKS Pencil Coil Connectors Terminals For Honda CBR600RR/F4I Yamaha R1/R6

[Wolfie666]

Finished!
Sort of...
Have to attend to a few details and iron out some bugs...

2019-05-01 14.21.25.jpg (1.15 MiB) Viewed 395 times

2019-05-01 14.21.35.jpg (1.16 MiB) Viewed 395 times

2019-05-01 14.23.11.jpg (1.15 MiB) Viewed 395 times

2019-05-01 14.23.21.jpg (1.13 MiB) Viewed 395 times

[wingrider]

Very nice!

[Rednaxs60]

Ditto! Very Nice

[Sugs]

And how loud are those pipes!

[Buli]

Very nice. Look like pro job.

[Wolfie666]

And how loud are those pipes!

I have 12" steel baffles in them, and the Webers are louder, unless you really get on it,
so they are coming out!

[Easter]

Very sharp ride. Good work. BOM material.