Home made FORK BRACE?

From basic novice to the hard core cutomizing. Sharing tips, tricks and knowledge. Feel
free to ask question or give us your "2 cents".

Moderators: sunnbobb, Neil, Forum Moderators

Post Reply
User avatar
BikeMaine
Gold Member
Gold Member
Posts: 1105
Joined: Sun Feb 07, 2016 7:57 pm
Location: Maine, U.S.A.

Home made FORK BRACE?

#1

Post by BikeMaine »

Have any of you made a fork brace?

I know I could buy one and be done with it, but I like to challenge myself from time to time and build something instead.

Between my lathe, drill press and MIG and TIG welders, I feel I could do it and make it look good.

Any photos or advice?
Kevin
1982 GL1100A
User avatar
Rat
Photo Gallery Admin
Photo Gallery Admin
Posts: 15457
Joined: Fri Oct 21, 2005 9:59 pm
My Album: https://www.ngwclub.com/gallery/v/wingmans/rat/
RIP: cookie
Location: Toronto .... Canada

Re: Home made FORK BRACE?

#2

Post by Rat »

Someone posted a nice home made on in a build thread lately .... can look for it right now and don't remember which thread ....

Gord (it was fairly recent tho' ....) Jones :roll:
"I'd rather Ride than Shine"
‘14 KLR650 ... not a rat ... yet
‘84 GL1200i ‘R2B6' (Rat to Be 6, the last, adopted by twowings)
My Original 'RAT' was a hybrid '82 CB900/1100F
User avatar
Rat
Photo Gallery Admin
Photo Gallery Admin
Posts: 15457
Joined: Fri Oct 21, 2005 9:59 pm
My Album: https://www.ngwclub.com/gallery/v/wingmans/rat/
RIP: cookie
Location: Toronto .... Canada

Re: Home made FORK BRACE?

#3

Post by Rat »

"I'd rather Ride than Shine"
‘14 KLR650 ... not a rat ... yet
‘84 GL1200i ‘R2B6' (Rat to Be 6, the last, adopted by twowings)
My Original 'RAT' was a hybrid '82 CB900/1100F
User avatar
ericheath
Honored Life Member
Honored Life Member
Posts: 9580
Joined: Wed Jul 29, 2009 11:20 am
Location: Winnipeg, Manituba

Re: Home made FORK BRACE?

#4

Post by ericheath »

I made one like that one. No drill press. The holes in my spacers are quite large, but as long as it’s tight and you use a little loctite, and it’s spaced properly, it seems to work. I need to get mine cleaned up with a router. I had an extra triple tree so I installed the extra one below the brace to mark the spacing. I assumed the forks run parallel to each other. Most fenders need the spacers to clear, but a different fender from more modern bikes might be found to fit above the brace.
Whatever I suggest here should be given ample time for a moderator to delicately correct. I apologize in advance.
77 WING, 1200 engine with 77 heads, cams, gl1100 foot pegs, Magna V65 front end, 764A carbs, [-gone Suzuki M109 monoshock--, replaced with gl1100 shocks] gl 1200 swing arm, gl1500 final drive, wheel and rear brakes Valkyrie seat, Meanstreak tank, Sportster pipes, Power Arc ignition off crank.
77 Wing. black
83 Wing, in pieces
"Continuing education is important even if the subject matter is fairly useless (as in this case)."---Greg Foresi
User avatar
BikeMaine
Gold Member
Gold Member
Posts: 1105
Joined: Sun Feb 07, 2016 7:57 pm
Location: Maine, U.S.A.

Re: Home made FORK BRACE?

#5

Post by BikeMaine »

Thank you!
Kevin
1982 GL1100A
User avatar
Brant
Board of Directors
Board of Directors
Posts: 10126
Joined: Fri Mar 25, 2005 11:31 am
My Album: http://www.ngwclub.com/gallery/v/wingmans/brant/
Location: Hastings, Nebraska, USA

Re: Home made FORK BRACE?

#6

Post by Brant »

I remember one made with two u bolts and angle iron.
83 GL 1100 bagger Ugly Betty
ALL WE WANT TO DO IS DRINK OUR ESPRESSO, RIDE OUR MACHINES, AND NOT BE HASSLED BY THE MAN
Owning a motorcycle is not a matter of life or death. It's much more important than that.
"Don't sweat the little things, guys, take care and appreciate all that you have around you!" - Fewman
NGWclub on Facebook
digschopper
Titanium Member
Titanium Member
Posts: 304
Joined: Tue Jan 04, 2011 12:33 pm
Location: Goatpoop ,florida

Re: Home made FORK BRACE?

#7

Post by digschopper »

Is this what you were looking for?
Attachments
IMG_20180127_093836726.jpg
IMG_20180127_093836726.jpg (416.39 KiB) Viewed 352 times
User avatar
Track T 2411
Honored Life Member
Honored Life Member
Posts: 8482
Joined: Thu May 29, 2008 9:37 pm
My Album: http://www.ngwclub.com/gallery/v/wingmans/Track+T+2411/
Location: Prairie du Sac Wisconsin

Re: Home made FORK BRACE?

#8

Post by Track T 2411 »

Brant wrote:I remember one made with two u bolts and angle iron.
Yes, I found that one recently, as well. It's on a 'rat' bike 1100. Old thread, though...
"I have no special talent. I am only passionately curious." - Albert Einstein

"He that is good with a hammer tends to think everything is a nail" - Abraham Maslow

"If you can't take the time to do it right the first time, how are you ever going to find the time to do it over?" -Unknown

Current Rides:
'Grumpy' - '81 Standard, now fully dressed.
'Layla' - '81 Standard w/dealer installed fairing and Hondaline bags.
'Scarlett' '76 'Survivor' nekkid as a j-bird!

Under Construction:
The 'Jalopy' '78-'79 Mash-up
'Quikie' '81 gl1100I back on the lift, project with the step-son!

In The Shed:
'81 gl1100I barn find aka "Josie, the farmer's daughter." (almost comatose build)
'77 gl1000, roller parts bike.
'82 gl1100I, 'Old Crusty' titled roller parts bike (free!)
'82 gl1100I, My first 'Wing, and an expensive lesson!
New2U Bike? Read Me.
Post Reply
  • Similar Topics
    Replies
    Views
    Last post

Return to “GoldWing UnderGround CustomiZing”