Wog's '78 Wild Child build

From basic novice to the hard core cutomizing. Sharing tips, tricks and knowledge. Feel
free to ask question or give us your "2 cents".

Moderators: sunnbobb, Neil, Forum Moderators

User avatar
wog
Platinum Member
Platinum Member
Posts: 1706
Joined: Fri Sep 16, 2011 9:08 am
Location: FL

Wog's '78 Wild Child build

Post #1 by wog » Fri Feb 07, 2014 12:14 pm

Decided to turn one of my '78 stock black wings into my official "UnderGround Custom" bike.

30k miles, titled and plated, stock everything except engine guards.

One of the bikes I started on a few years ago, just never did much with it. I have my original '78 black so this one is going to be my victim. :twisted:

First mod (and easiest) will be a Sporter seat I picked up awhile back at the local flea market in place of the stock seat I recovered with the standard Ebay replacement cover. Never liked the quality of the cover.

Second, custom aluminum cooling fins incorporated onto the valve cover sides. Kinda like the old Beemers have.
Valve cover fins rendering.jpg


Third, replace the carb rack with a single conversion I have from another bike.
I love the look of velocity stacks on hot rods, so I'm going to go with that look out the top. Not sure if they will be just for show, or functional.
They won't be true velocity stacks, but my very own (read Cheap) version made from a set of stainless steel sauce cups from Sam's Club at a cost of less than $4.00 for 12. I'll cut off the bottoms and weld them to stainless tubing the same diameter.
Not sure if I keep them polished, powder coat them, or as pictured below with heat marks made with a propane torch. Probably go with the multi-level angled look, but that will be fine tuned later...
You do not have the required permissions to view the files attached to this post.
'75 GL1000 blue/green - naked - "Christine" http://www.ngwclub.com/forum/viewtopic.php?f=30&t=46408
'78 GL1000 yellow - modified naked - "wild child" http://www.ngwclub.com/forum/viewtopic.php?f=16&t=51534
'78 GL1000 black - becoming the "adventure bike" http://www.ngwclub.com/forum/viewtopic.php?f=16&t=56788
'84 GL1200 Standard - wineberry #1 http://www.ngwclub.com/forum/viewtopic.php?f=30&t=55155
and a few others (stopped counting after a dozen)

Great to keep these old 'Wings flying on down the road.

User avatar
wog
Platinum Member
Platinum Member
Posts: 1706
Joined: Fri Sep 16, 2011 9:08 am
Location: FL

Re: Wog's '78 Wild Child build

Post #2 by wog » Fri Feb 07, 2014 12:16 pm

The heated stacks (cups)...
You do not have the required permissions to view the files attached to this post.
'75 GL1000 blue/green - naked - "Christine" http://www.ngwclub.com/forum/viewtopic.php?f=30&t=46408
'78 GL1000 yellow - modified naked - "wild child" http://www.ngwclub.com/forum/viewtopic.php?f=16&t=51534
'78 GL1000 black - becoming the "adventure bike" http://www.ngwclub.com/forum/viewtopic.php?f=16&t=56788
'84 GL1200 Standard - wineberry #1 http://www.ngwclub.com/forum/viewtopic.php?f=30&t=55155
and a few others (stopped counting after a dozen)

Great to keep these old 'Wings flying on down the road.

User avatar
delling3
Gold Member
Gold Member
Posts: 1117
Joined: Mon Sep 17, 2012 8:14 am
Location: Sterling Heights, Michigan

Re: Wog's '78 Wild Child build

Post #3 by delling3 » Fri Feb 07, 2014 12:22 pm

I am subscribed . . .
delling3

Currently Bikeless

Previous:
1978 GL1000 - JUNE 2017 BOTM: Sold
2006 Kawasaki Concours: Sold
1995 Kawasaki Concours: Crashed/totalled.
1976 GL1000: LAST RESTORATION, sold
1981 Honda CB900F Supersport: 3rd restoration, sold.
1979 Yamaha XS-750F: 2nd restoration, sold.
1982 Honda FT-500 Ascot: First (only) new bike. Family forces sale.
1973 CB500 Four: First restoration, long gone.
1972 Suzuki TS-100: First bike, sold.

Only dead fish go with the flow . . .

User avatar
wog
Platinum Member
Platinum Member
Posts: 1706
Joined: Fri Sep 16, 2011 9:08 am
Location: FL

Re: Wog's '78 Wild Child build

Post #4 by wog » Fri Feb 07, 2014 1:45 pm

delling3 wrote:I am subscribed . . .

Hope I don't overwhelm you with subscribed emails as I plan on taking pics and posting as I go. lolol

First remove the valuable '75 blue emblems from a couple of pitted chromed covers with a small metal ruler.
Nice that they are the press-in style, no small screws to break off.
valve cover fins 003.jpg

valve cover fins 002.jpg


Onto the mill.
I used a scrap block of alum to mount them as I didn't want to remove my vices.
Drill mounting holes (13/64") for 1/4" bolts. "Close" is good enough.
valve cover fins 004.jpg


Just used the hand drill to tap, no precision here
valve cover fins 005.jpg


Bolted down...
valve cover fins 006.jpg


I was planning on profile milling a rectangle and plug welding the fin block in, but I think I'll try just surfacing the original fins down and see if that will work.
You do not have the required permissions to view the files attached to this post.
'75 GL1000 blue/green - naked - "Christine" http://www.ngwclub.com/forum/viewtopic.php?f=30&t=46408
'78 GL1000 yellow - modified naked - "wild child" http://www.ngwclub.com/forum/viewtopic.php?f=16&t=51534
'78 GL1000 black - becoming the "adventure bike" http://www.ngwclub.com/forum/viewtopic.php?f=16&t=56788
'84 GL1200 Standard - wineberry #1 http://www.ngwclub.com/forum/viewtopic.php?f=30&t=55155
and a few others (stopped counting after a dozen)

Great to keep these old 'Wings flying on down the road.

User avatar
Casper
SUPER BIKER!!!!
SUPER BIKER!!!!
Posts: 3338
Joined: Sun Aug 07, 2011 9:54 am
Location: Calgary, Canada

Re: Wog's '78 Wild Child build

Post #5 by Casper » Fri Feb 07, 2014 1:50 pm

:popcorn:

Looks like a fun project to watch.
1976 LTD, Being Returned to Stock
Standard 1976 GL1000 Being Morphed into the Alberta Super Clipper

User avatar
fish
SUPER BIKER!!!!
SUPER BIKER!!!!
Posts: 3110
Joined: Wed Feb 18, 2009 1:50 pm
Location: tucson

Re: Wog's '78 Wild Child build

Post #6 by fish » Fri Feb 07, 2014 1:57 pm

Wog this all looks great!
Thaqnk yopu for taking the time to document it all & keeping us posted.
The valve cover ideer and velocity stacks are great..
I have often thought of exactly the same things.
I thought real velocity stacks sticking out of the shelter would look very cool but be NOISY! plus if I ever left it outside in a rainstorm I would have to carry a sparkplug socket with me.
I am daydreamiong of valvecovers that look like the old Edelbrock finned Ford flathead V-8 heads
flathead.jpg
You do not have the required permissions to view the files attached to this post.
Timothy Mark Fisher
Catalina Arizona
"ride it.. don't be one of those guys who will fix it 'til it's broken" (JDVorchek)
"It is not logic or economics that drive a motorcyclist but passion!" (bugdaddy66)
"I fully agree with fish, well at least 27% of the time."(Casper)
"Why do you have to ruin a perfectly good thread with common sense"(Placerville)
"my best guess for an answer would be a stream of complex expletives" (Transitman)
"I like a cold beer with my beer" (OldeWing)
"Most of us like the sport of wrenching too." (fred camper)
"Now go ride the heck out of it, til mother says do your chores"(Gowing)
"I agree with Fish" (Salukispeed)

User avatar
wog
Platinum Member
Platinum Member
Posts: 1706
Joined: Fri Sep 16, 2011 9:08 am
Location: FL

Re: Wog's '78 Wild Child build

Post #7 by wog » Fri Feb 07, 2014 2:54 pm

Might end up going that route Fish.
Even though it's much more programming, might be the shortest way in the long run.
I remember seeing an aftermarket GL1000 cover kinda like that, but it's been many years. Think I've only seen one pair.

Started to fly cut the covers and I think my neighbors from at least a mile away were holding their ears! :shock:

Changed over to a indexable mill and was able to knock it down without all the screaming.
You do not have the required permissions to view the files attached to this post.
Last edited by wog on Fri Feb 07, 2014 3:06 pm, edited 1 time in total.
'75 GL1000 blue/green - naked - "Christine" http://www.ngwclub.com/forum/viewtopic.php?f=30&t=46408
'78 GL1000 yellow - modified naked - "wild child" http://www.ngwclub.com/forum/viewtopic.php?f=16&t=51534
'78 GL1000 black - becoming the "adventure bike" http://www.ngwclub.com/forum/viewtopic.php?f=16&t=56788
'84 GL1200 Standard - wineberry #1 http://www.ngwclub.com/forum/viewtopic.php?f=30&t=55155
and a few others (stopped counting after a dozen)

Great to keep these old 'Wings flying on down the road.

User avatar
wog
Platinum Member
Platinum Member
Posts: 1706
Joined: Fri Sep 16, 2011 9:08 am
Location: FL

Re: Wog's '78 Wild Child build

Post #8 by wog » Fri Feb 07, 2014 2:58 pm

I was planning on milling the fins from a solid block, but may go this route with seperate bars.

I want to get close to matching the engine guard angle with the fins. I don't really like having the guards on my bikes, but this bike would not be one I want knocked over and have to replace the covers.
(Yes, the silly clamp for the foot peg will be removed.) shakehands
You do not have the required permissions to view the files attached to this post.
'75 GL1000 blue/green - naked - "Christine" http://www.ngwclub.com/forum/viewtopic.php?f=30&t=46408
'78 GL1000 yellow - modified naked - "wild child" http://www.ngwclub.com/forum/viewtopic.php?f=16&t=51534
'78 GL1000 black - becoming the "adventure bike" http://www.ngwclub.com/forum/viewtopic.php?f=16&t=56788
'84 GL1200 Standard - wineberry #1 http://www.ngwclub.com/forum/viewtopic.php?f=30&t=55155
and a few others (stopped counting after a dozen)

Great to keep these old 'Wings flying on down the road.

User avatar
duke182
SUPER BIKER!!!!
SUPER BIKER!!!!
Posts: 3373
Joined: Mon Jul 05, 2010 11:33 pm
My Album: http://ngwclub.com/gallery/v/wingmans/duke182/
Location: hope,ark

Re: Wog's '78 Wild Child build

Post #9 by duke182 » Fri Feb 07, 2014 8:55 pm

Your work is looking good.

I seem to remember someone on the board buying a bike that had finned covers.
It was stated by someone else that they believed them to be mickey thompson pieces.

I'd make a great witness. dont you think? Ha ha!
God bless those who protect our freedom, at every level

Knees in the breeze makes miles of smiles

"Strive for progress, not perfection"-a wise man

1984 1200 standard
Image
click pic to see my gallery

vote in my poll

User avatar
sunnbobb
Facebook Admin
Facebook Admin
Posts: 21060
Joined: Thu Jan 10, 2008 4:09 pm
My Album: http://www.ngwclub.com/gallery/v/wingmans/sunnbobb/
Location: LaConner, WA

Re: Wog's '78 Wild Child build

Post #10 by sunnbobb » Fri Feb 07, 2014 9:25 pm

Thanks for posting, you are saving me alot of time. I planned on doing a flathead set myself.
I found the end of the internet

---- Bradshaw Bikes custom polishing for your wing. Visit us on facebook!

1978 Learning Experience
1980 County Road Hauler "Brain Damage"
1978 Cafe Custom Gl1000 "Vyper"
1977 Bulldog Inspired "Vaincre"
1981 Street Fighter GL1100 "No Quarter"
1983 Supercharged Street Drag "Anubis" (in worx)
1983 gl1100 mint restoration "Kristen"

User avatar
fish
SUPER BIKER!!!!
SUPER BIKER!!!!
Posts: 3110
Joined: Wed Feb 18, 2009 1:50 pm
Location: tucson

Re: Wog's '78 Wild Child build

Post #11 by fish » Fri Feb 07, 2014 9:30 pm

sunnbobb wrote:Thanks for posting, you are saving me alot of time. I planned on doing a flathead set myself.

yes! action1
wire wheels painted red
wide whitewalls
dual strombergs
beehive air filters
suede paint
lakes pipes
kinda' a '50's hotrod theme
Timothy Mark Fisher
Catalina Arizona
"ride it.. don't be one of those guys who will fix it 'til it's broken" (JDVorchek)
"It is not logic or economics that drive a motorcyclist but passion!" (bugdaddy66)
"I fully agree with fish, well at least 27% of the time."(Casper)
"Why do you have to ruin a perfectly good thread with common sense"(Placerville)
"my best guess for an answer would be a stream of complex expletives" (Transitman)
"I like a cold beer with my beer" (OldeWing)
"Most of us like the sport of wrenching too." (fred camper)
"Now go ride the heck out of it, til mother says do your chores"(Gowing)
"I agree with Fish" (Salukispeed)

User avatar
HOTT
Run Executive
Run Executive
Posts: 3170
Joined: Sun Aug 02, 2009 6:48 pm
My Album: http://www.ngwclub.com/gallery3/index.php/wingmans/HOTT
Location: Spring,TX
Contact:

Re: Wog's '78 Wild Child build

Post #12 by HOTT » Sat Feb 08, 2014 12:25 am

sunnbobb wrote:Thanks for posting, you are saving me alot of time. I planned on doing a flathead set myself.


Me TOO!! Argh! :lol: :lol:
Go get 'em Wog.
If we can't fix it, we can fix it so no one else can.
the Condor BOTY 2011
Ol' Sparky BOTM Dec. 2011
Lucky #13 BOTY 2018

User avatar
jimmyz3286
Silver Member
Silver Member
Posts: 629
Joined: Sat May 11, 2013 9:04 pm
Location: Mount Vernon, Wa

Re: Wog's '78 Wild Child build

Post #13 by jimmyz3286 » Sat Feb 08, 2014 12:54 am

I'm in for the ride on this one. A man with a vision, make it be!
"The rain collected pools of images at my feet and they asked the direction to the ocean."

1982 GL1100 Silverback
2004 Roadstar For Sale
1981 CX500 café project for Anakin

User avatar
Roady
Member Relations &_Graphics
Member Relations &_Graphics
Posts: 11933
Joined: Wed Jun 20, 2007 2:35 pm
Location: Port St. John, FL

Re: Wog's '78 Wild Child build

Post #14 by Roady » Sat Feb 08, 2014 8:40 am

I'm in, this is already very interesting. Go get 'em, Man!

User avatar
wog
Platinum Member
Platinum Member
Posts: 1706
Joined: Fri Sep 16, 2011 9:08 am
Location: FL

Re: Wog's '78 Wild Child build

Post #15 by wog » Sat Feb 08, 2014 12:44 pm

I thought I had an extra pair of covers that weren't chromed. No luck.
I tried bead blasting the one I milled down and the plating just laughed at it.
If anyone has a good way to easily remove the chrome and nickel underneath, please let me know.

So I decided to try another pair, and whatdoyaknow, comes off as easy as paint! dancr
Guess there were many "grades" of plating back in the '80's.
Either that, or whatever polish/clearcoat on this pair peels like bad chrome.
Maybe Sunnbobb can tell just by looking at the pic.

Here's the second pair after blasting 1/2 under the badge.
valve cover fins 014.jpg

And making sure all the nickel is removed so I can tig it cleanly.
valve cover fins 015.jpg


Next I tested welding to the first cover to see if the cast aluminum would allow a good bead.
Ground down the chrome in just that area on a sander.
I had a heck of a time trying to tig holes in a GL1000 water pump cover recently. Terrible grade of aluminum to weld.
These worked fine.

valve cover fins 013.jpg
You do not have the required permissions to view the files attached to this post.
'75 GL1000 blue/green - naked - "Christine" http://www.ngwclub.com/forum/viewtopic.php?f=30&t=46408
'78 GL1000 yellow - modified naked - "wild child" http://www.ngwclub.com/forum/viewtopic.php?f=16&t=51534
'78 GL1000 black - becoming the "adventure bike" http://www.ngwclub.com/forum/viewtopic.php?f=16&t=56788
'84 GL1200 Standard - wineberry #1 http://www.ngwclub.com/forum/viewtopic.php?f=30&t=55155
and a few others (stopped counting after a dozen)

Great to keep these old 'Wings flying on down the road.


Return to “GoldWing UnderGround CustomiZing”

Who is online

Users browsing this forum: DrVMAX and 1 guest