New to bikes need opinions

Discuss everything about Honda GoldWing. Feel free to ask any question related to GoldWing.

Moderators: CYBORG, Oldewing, robin1731, Forum Moderators

Post Reply
User avatar
Whiskerfish
President
President
Posts: 36852
Joined: Thu Feb 16, 2006 9:34 pm
My Album: http://www.ngwclub.com/gallery/v/wingmans/whiskerfish/
Location: Norfolk Va

Re: New to bikes need opinions

#16

Post by Whiskerfish »

Go slow. Concentrate on one task at a time. Take lots of cell phone pictures. Do not force anything. Thinks may go sideways they occasionally do, don't panic, stop and ask questions. Start a thread in the restorations forum and plenty of good advice will be provided.

We all started off as novices and some of us had to learn hard lessons. But that is how you become good.
"Agreement is not a requirement for Respect" CDR Michael Smith USN (Ret) 2017
"The book is wrong, this whole Conclusion is Fallacious" River Tam
2008 GL1800 IIIA "TH3DOG"
1975/6/7/8/9 Arthur Fulmer Dressed Road bike
1975 Naked Noisy and Nasty in town bike
and a whole garage full of possibilities!!

Psst. oh and by the way CHANGE YOUR BELTS!!!!
User avatar
Rat
Photo Gallery Admin
Photo Gallery Admin
Posts: 15457
Joined: Fri Oct 21, 2005 9:59 pm
My Album: https://www.ngwclub.com/gallery/v/wingmans/rat/
RIP: cookie
Location: Toronto .... Canada

Re: New to bikes need opinions

#17

Post by Rat »

Experienced Supervisor ... 50 years experience supervising the best old Goldwing mechanics around ...

Will work for beer ... anim-cheers1

Gord(references available)Jones :joker
"I'd rather Ride than Shine"
‘14 KLR650 ... not a rat ... yet
‘84 GL1200i ‘R2B6' (Rat to Be 6, the last, adopted by twowings)
My Original 'RAT' was a hybrid '82 CB900/1100F
User avatar
robin1731
Membership Admin
Membership Admin
Posts: 21724
Joined: Mon May 29, 2006 8:31 am
Location: Decatur, Indiana

Re: New to bikes need opinions

#18

Post by robin1731 »

Rat wrote: Sat Nov 13, 2021 6:06 pm Experienced Supervisor ... 50 years experience supervising the best old Goldwing mechanics around ...

Will work for beer ... anim-cheers1

Gord(references available)Jones :joker
I can vouch for him. anim-cheers1 shakehands lolol
1976 Goldwing Super Sport
1985 Honda Elite
1976 KZ900 Dragbike
1992 ZX7 Dragbike (KZ900 style motor w/NOS)
and a rotation of various purchases
Randakk approved Carb Rebuilder
User avatar
Whiskerfish
President
President
Posts: 36852
Joined: Thu Feb 16, 2006 9:34 pm
My Album: http://www.ngwclub.com/gallery/v/wingmans/whiskerfish/
Location: Norfolk Va

Re: New to bikes need opinions

#19

Post by Whiskerfish »

robin1731 wrote: Sat Nov 13, 2021 10:55 pm
Rat wrote: Sat Nov 13, 2021 6:06 pm Experienced Supervisor ... 50 years experience supervising the best old Goldwing mechanics around ...

Will work for beer ... anim-cheers1

Gord(references available)Jones :joker
I can vouch for him. anim-cheers1 shakehands lolol
Seconded action1 action1 action1 lolol lolol lolol lolol
"Agreement is not a requirement for Respect" CDR Michael Smith USN (Ret) 2017
"The book is wrong, this whole Conclusion is Fallacious" River Tam
2008 GL1800 IIIA "TH3DOG"
1975/6/7/8/9 Arthur Fulmer Dressed Road bike
1975 Naked Noisy and Nasty in town bike
and a whole garage full of possibilities!!

Psst. oh and by the way CHANGE YOUR BELTS!!!!
Pb9717
Cast Iron Member
Cast Iron Member
Posts: 81
Joined: Tue Aug 27, 2019 8:07 pm
Location: Loveland OH

Re: New to bikes need opinions

#20

Post by Pb9717 »

Congrats on the purchase. That bikes gonna be worlds of fun. I have nothing to add as the pro's above have guided you very well, and all I can do is recommend coming back when you run into a snag and ask for help. These types of forums bring out the best in folks. And ditto on the brake work. Those old rubber hoses can fail at the worst times. Caliper rebuilds are easy ( just two seals) and the rear master will likely be a bit messy internally as well if it hasn't been rebuilt once before. I would look for a craftsman torque wrench, and you'll need some ring clip pliers to remove some parts on the bike. Maybe a ratcheting breaker bar, and a 24mm socket for the rear axel. Harbor Freight may become one of your new favorite stores. Lotsa fun ahead. Enjoy you new toy. Many smiles await.
(2) 82' GL1100's
99' Triumph Thunderbird Sport 900
2006 Triumph Speed Triple
Cincinnati OH USA
Explorer
Titanium Member
Titanium Member
Posts: 329
Joined: Sun Feb 02, 2014 1:00 pm
Location: Texas

Re: New to bikes need opinions

#21

Post by Explorer »

And JIS tip screwdrivers, too. tumb2 Although they look like Phillips head screws, they aren't.

JIS = Japanese Industry Standard.
____________________________________

This "may" be the best advise given so far in this thread.

Through sheer ignorance on both sides this is why Japanese bikes in general got a bad reputation from the seventies probably to this day. The Japanese didn't tell the western redneckese that JIS was different to Phillips, and the redneckese didn't ask. The upshot of all this was that all Japanese bikes where tarred with a reputation of being made of crap aluminum. If I've heard the quote "Screws wallow out as soon as you lay a screwdriver on 'em", once, I've heard it a hundred times.

If this unfortunate misinterpretation of facts hadn't happened, we'd all own a set of JIS screwdrivers and everybody would be happy.

Except of course for those hard nose Harley riders.
zxWIZxz
Brass Member
Brass Member
Posts: 23
Joined: Tue Nov 09, 2021 8:15 pm

Re: New to bikes need opinions

#22

Post by zxWIZxz »

So I've started the job finally. Sort of. Lol. I am draining the oil and Coolant overnight. I want to take it super slow. So far I have a few questions. First, I plan on cleaning all of the bolts with brake cleaner and a toothbrush wondering if that sounds good or if there is a better way. Also wondering if I should clean the insides of the oil filter cap, coolant drain cover etc...
Lastly, I seem to be missing the "washer" that sits on the spring in the oil filter cover. The tutorial says not to lose it and that it's common for it to get stuck to the oil filter and get tossed. Not sure if that's what happened to it but I looked in the drain pan, on the filter. In the housing etc and I can't find it. Apparently it's been run that way since the last change atleast. Should I just go without or try to track one down?
Wiz
1982 honda goldwing gl1100
Southern/mid NH USA
User avatar
Sidecar Bob
Honored Life Member
Honored Life Member
Posts: 7633
Joined: Sun Jun 11, 2006 10:14 pm
Location: Kawartha Lakes, Ontario

Re: New to bikes need opinions

#23

Post by Sidecar Bob »

Your local Honda dealer should be able to get the washer for you.

If the bolt heads are just dirty/greasy I would clean them with mineral spirits and a brush, especially if you are cleaning them while they are in the engine (some brake cleaners can harm paint).
Mr. Honda ('83 GL1100/Dnepr) summer How a motorcycle evolves thread
The Famous Eccles ('84 CX650EI/VeloUral) winter Never Ending Build (CX500forum)
Click: Colour schematics for all GL1000 & GL1100 and GL1200 standard models plus instructions on how to download the full size version
"A guy with two sidecars can't be all bad." - Cookie
Another guy with two sidecars..... Hmmmm... must be something to that....
User avatar
Whiskerfish
President
President
Posts: 36852
Joined: Thu Feb 16, 2006 9:34 pm
My Album: http://www.ngwclub.com/gallery/v/wingmans/whiskerfish/
Location: Norfolk Va

Re: New to bikes need opinions

#24

Post by Whiskerfish »

Yes the correct spring and washer are very important.
"Agreement is not a requirement for Respect" CDR Michael Smith USN (Ret) 2017
"The book is wrong, this whole Conclusion is Fallacious" River Tam
2008 GL1800 IIIA "TH3DOG"
1975/6/7/8/9 Arthur Fulmer Dressed Road bike
1975 Naked Noisy and Nasty in town bike
and a whole garage full of possibilities!!

Psst. oh and by the way CHANGE YOUR BELTS!!!!
toomanybikes
Billet Alum. Member
Billet Alum. Member
Posts: 227
Joined: Sun Oct 27, 2019 6:38 am

Re: New to bikes need opinions

#25

Post by toomanybikes »

zxWIZxz wrote: Sun Mar 06, 2022 8:21 pm First, I plan on cleaning all of the bolts with brake cleaner and a toothbrush wondering if that sounds good or if there is a better way.
For cleaning bolts, mainly smaller ones, I generally put them in a glass jar, spray with good amount of PB blaster, spin the jar around and let them sit. PB blaster is great, I buy it by the gallon, but be careful not to get too much in/on you. The "PB" stands for lead, not peanut butter.

If you take the radiator off for other reasons, do the water pump at the same time. Once you get to the pump, another important task will be cleaning the gasket surface without scarring the soft aluminum. The engine side will be trickiest since it will have less room to work than the cover you take off.

After trying numerous tools, the best one I've found is a carbide gasket scraper. But you have to be very careful because carbide will definitely gouge Al if attached from an angle. Many recommend plastic scrapers, but I've never found them to be strong enough to remove petrified gaskets from 40 year old bikes.
Greater Boston MA, USA
Stable as of 26Dec22: '81 GL1100, '10 Bonnie SE, '86 Yamaha Radian, '83 Suzuki GS650L, '14 Moto Guzzi California, '85 Honda V30 Magna
User avatar
flyin900
Gold Member
Gold Member
Posts: 1489
Joined: Sun Jan 10, 2010 3:50 pm
Location: Canada

Re: New to bikes need opinions

#26

Post by flyin900 »

A small can of aircraft paint stripper (1 Liter) or spray can is also good to have on hand. Hardware store is the source for me. I use it on those stuck on old gaskets with a small hobby paint brush used to apply it. It will soften the old gasket making the scraping much easier. It is great for removing old clearcoat first on aluminum covers that you wish to polish back to almost new again.
Current Bikes:

1966 CL77 - Honda 305cc - Dual purpose - "Gentleman's Scrambler" was a period moniker.
1967 CL175K0 - Low production number with #802 engine serial- winter 2019/2020 full restoration.
1972 CB350F - Baby Four with low mileage - Cosmetic refresh to the next level 2021/2022.
1978 CB550K - Very original bike with only 7499 Km. from new - light cleanup and refresh done.
1983 CB1100F - Canadian model - DOHC Supersport in pristine low kilometre condition from new.
1984 GL1200 - Standard model in showroom condition - two owner bike from new.
1984 CX650E - Restored summer 2017 - a rare Eurosport model - excellent one owner bike.
User avatar
Sidecar Bob
Honored Life Member
Honored Life Member
Posts: 7633
Joined: Sun Jun 11, 2006 10:14 pm
Location: Kawartha Lakes, Ontario

Re: New to bikes need opinions

#27

Post by Sidecar Bob »

I understood that "PB" stands for Parts Blaster.
The MSDS doesn't say anything about lead
https://blasterproducts.com/wp-content/ ... -12-13.pdf
Mr. Honda ('83 GL1100/Dnepr) summer How a motorcycle evolves thread
The Famous Eccles ('84 CX650EI/VeloUral) winter Never Ending Build (CX500forum)
Click: Colour schematics for all GL1000 & GL1100 and GL1200 standard models plus instructions on how to download the full size version
"A guy with two sidecars can't be all bad." - Cookie
Another guy with two sidecars..... Hmmmm... must be something to that....
zxWIZxz
Brass Member
Brass Member
Posts: 23
Joined: Tue Nov 09, 2021 8:15 pm

Re: New to bikes need opinions

#28

Post by zxWIZxz »

Thanks guys
Wiz
1982 honda goldwing gl1100
Southern/mid NH USA
zxWIZxz
Brass Member
Brass Member
Posts: 23
Joined: Tue Nov 09, 2021 8:15 pm

Re: New to bikes need opinions

#29

Post by zxWIZxz »

ImageSo I don't know if it's real or if my eyes are playing tricks on me. But it would appear as though my Oil has a green tint to it. Is this normal or should I be concerned? There's no frothiness or bubbles. Other than the tint it looks normal
Attachments
20220308_095146.jpg
20220308_095146.jpg (166.82 KiB) Viewed 188 times
20220308_095122.jpg
20220308_095122.jpg (246.36 KiB) Viewed 188 times
20220308_095115.jpg
20220308_095115.jpg (219.62 KiB) Viewed 188 times
Wiz
1982 honda goldwing gl1100
Southern/mid NH USA
Explorer
Titanium Member
Titanium Member
Posts: 329
Joined: Sun Feb 02, 2014 1:00 pm
Location: Texas

Re: New to bikes need opinions

#30

Post by Explorer »

Duckhams Q oil is green, it's popular in the UK, maybe here too now IDK, but I can't think of anything in the motor that would turn it green.
Post Reply
  • Similar Topics
    Replies
    Views
    Last post

Return to “GoldWing Tech Discussions”