Brakes; getting closer. Opinion on pads and more

Discuss everything about Honda GoldWing. Feel free to ask any question related to GoldWing.

Moderators: CYBORG, Oldewing, robin1731, Forum Moderators

Post Reply
User avatar
bonestock3
Chrome Member
Chrome Member
Posts: 155
Joined: Wed Jan 21, 2015 5:47 pm
Location: Bronx, NY
Contact:

Brakes; getting closer. Opinion on pads and more

#1

Post by bonestock3 »

Looking at this set
To replace my current brakes
image.jpg
image.jpg (19.7 KiB) Viewed 291 times
image.jpg
image.jpg (19.7 KiB) Viewed 291 times
Bought a torque wrench to get into the brakes. Noticed how the pads are crumbling apart; ordering now.

The discs don't feel bad but might replace while I'm at it. Might go slotted/drilled. Any recommendations?
Bonestock©
1979 GL1000 - Avomew
User avatar
BlueThunder
Platinum Member
Platinum Member
Posts: 1612
Joined: Fri Nov 07, 2008 4:39 pm
Location: Sarasota, Florida

Re: Brakes; getting closer. Opinion on pads and more

#2

Post by BlueThunder »

Rather than Kevlar, I prefer the EBC semi-sintered pads. They were called "semi-metallic" back in the day. Better stoppage without sacrificing wear. Does not damage brake rotors as well.
Last edited by BlueThunder on Sat May 23, 2015 11:06 pm, edited 1 time in total.
...Brian
2014 CTX1300 Deluxe - BlackThunder aka Predator
1977 GL1000 - Ox
User avatar
chewy999
SUPER BIKER!!!!
SUPER BIKER!!!!
Posts: 3214
Joined: Tue Oct 16, 2012 11:21 am
Location: Haddenham, Cambs, UK

Re: Brakes; getting closer. Opinion on pads and more

#3

Post by chewy999 »

My pads of choice are EBC, but sure others will have their own favourites.

anim-cheers1
Previous Rides,
1980 CB250N Good to learn on
1981 CX500 good mid range tourer, went to Austria on it!
1983 GL1100C Pride and joy, sold when I bought my 1st house, big mistake
1985 GL650 Silverwing another mistake, horrible bike
1986 CBX550 Good commuter
1989 Suzuki GS750 (1976) cheap and cheerful until a dog ran out in front of me on Xmas Eve, 1991
Current bikes
2010 CB1300 back on a bike after 19 years, two divorces, children grown up etc
1980 GL1100 NOW ON THE ROAD, still use CB1300.
User avatar
chewy999
SUPER BIKER!!!!
SUPER BIKER!!!!
Posts: 3214
Joined: Tue Oct 16, 2012 11:21 am
Location: Haddenham, Cambs, UK

Re: Brakes; getting closer. Opinion on pads and more

#4

Post by chewy999 »

bonestock3 wrote:
Bought a torque wrench to get into the brakes. Noticed how the pads are crumbling apart; ordering now.
Why did you buy a torque wrench to get into your brakes? Surely you would be loosening stuff off. :-?

My (limited) understanding, is that you shouldn't use a torque wrench as a normal lever, just for what it says on the tin!

anim-cheers1
Previous Rides,
1980 CB250N Good to learn on
1981 CX500 good mid range tourer, went to Austria on it!
1983 GL1100C Pride and joy, sold when I bought my 1st house, big mistake
1985 GL650 Silverwing another mistake, horrible bike
1986 CBX550 Good commuter
1989 Suzuki GS750 (1976) cheap and cheerful until a dog ran out in front of me on Xmas Eve, 1991
Current bikes
2010 CB1300 back on a bike after 19 years, two divorces, children grown up etc
1980 GL1100 NOW ON THE ROAD, still use CB1300.
User avatar
bonestock3
Chrome Member
Chrome Member
Posts: 155
Joined: Wed Jan 21, 2015 5:47 pm
Location: Bronx, NY
Contact:

Re: Brakes; getting closer. Opinion on pads and more

#5

Post by bonestock3 »

I've been loyal EBC but at this price I had to ask.

I read a sticky on brake job and it was listed as a required tool; it'll come in handy eventually
Bonestock©
1979 GL1000 - Avomew
User avatar
Sagebrush
Run Executive
Run Executive
Posts: 6465
Joined: Wed Aug 15, 2007 10:35 pm
My Album: http://www.ngwclub.com/gallery/v/wingmans/album269/
Location: Raleigh, NC

Re: Brakes; getting closer. Opinion on pads and more

#6

Post by Sagebrush »

Can't go wrong buying a torque wrench, only use it to tighten bolts though. Never to loosen. I'm on the EBC bus as well.
Dean Spalding
Raleigh, NC

"Two things are infinite: the universe and human stupidity; and I'm not sure about the universe." - Albert Einstein

'82 Yellow GL1100
'81 Blue GL1100

My Gallery
My 1100 Build Thread
User avatar
NCScooter
Gold Member
Gold Member
Posts: 1100
Joined: Thu Jul 11, 2013 4:55 pm
My Album: http://ngwclub.com/gallery3/index.php/w ... ter?page=1
Location: Lovely Fayetteville, North Carolina

Re: Brakes; getting closer. Opinion on pads and more

#7

Post by NCScooter »

I had a pair of kevlar (ebc) on the back, did not last as long as I would have hoped. I would imagine they'd get ate up on the front.
I need to remember to keep my expectations tiny so I don't end up so whiny.
1976 CB400f
Image 1977 GL1000-The Breeze
I'm so special, my short bus only has two wheels!
User avatar
zman
Gold Member
Gold Member
Posts: 1237
Joined: Fri Sep 07, 2012 3:33 pm
Location: Covina Ca.

Re: Brakes; getting closer. Opinion on pads and more

#8

Post by zman »

For what its worth I have those pads, almost 4K on them and still look pretty thick, had them off the other day to install the new front tire, stops rapid enough but who's to say whats enough.
1980 1100 Interstate, 1978 GL1000
User avatar
bonestock3
Chrome Member
Chrome Member
Posts: 155
Joined: Wed Jan 21, 2015 5:47 pm
Location: Bronx, NY
Contact:

Re: Brakes; getting closer. Opinion on pads and more

#9

Post by bonestock3 »

Ha thanks! Only use to tighten not loosen - that's sound.
Bonestock©
1979 GL1000 - Avomew
User avatar
robin1731
Membership Admin
Membership Admin
Posts: 21724
Joined: Mon May 29, 2006 8:31 am
Location: Decatur, Indiana

Re: Brakes; getting closer. Opinion on pads and more

#10

Post by robin1731 »

bonestock3 wrote:Ha thanks! Only use to tighten not loosen - that's sound.

If it is the "clicker" type you should also set it to the lowest setting after you are finished using it. Don't put it back in the tool box with it still set to 80lbs-ft. (that's just a number I pulled from the air)

If it came in a case use it. Torque wrench's are fairly delicate and calibrated instruments. Some of the cost a lot of money. Take good care of it. Some say they should be recalibrated every few years.
1976 Goldwing Super Sport
1985 Honda Elite
1976 KZ900 Dragbike
1992 ZX7 Dragbike (KZ900 style motor w/NOS)
and a rotation of various purchases
Randakk approved Carb Rebuilder
User avatar
NCScooter
Gold Member
Gold Member
Posts: 1100
Joined: Thu Jul 11, 2013 4:55 pm
My Album: http://ngwclub.com/gallery3/index.php/w ... ter?page=1
Location: Lovely Fayetteville, North Carolina

Re: Brakes; getting closer. Opinion on pads and more

#11

Post by NCScooter »

Not to stir up a hornet's nest, but it seems I read somewhere the bar/pointer thingy were more accurate. Is this true?
I need to remember to keep my expectations tiny so I don't end up so whiny.
1976 CB400f
Image 1977 GL1000-The Breeze
I'm so special, my short bus only has two wheels!
User avatar
robin1731
Membership Admin
Membership Admin
Posts: 21724
Joined: Mon May 29, 2006 8:31 am
Location: Decatur, Indiana

Re: Brakes; getting closer. Opinion on pads and more

#12

Post by robin1731 »

NCScooter wrote:Not to stir up a hornet's nest, but it seems I read somewhere the bar/pointer thingy were more accurate. Is this true?
The beam type has always been given that reputation. I won't say either way. But you do need to be careful with the way you store those too. I have both a beam type and 3 "clicker" type. The beam can be a pain to use at times. You do have to be able to see it directly to read it. Not always easy when working on an assembled bike. ;)
1976 Goldwing Super Sport
1985 Honda Elite
1976 KZ900 Dragbike
1992 ZX7 Dragbike (KZ900 style motor w/NOS)
and a rotation of various purchases
Randakk approved Carb Rebuilder
User avatar
CYBORG
Moderator
Moderator
Posts: 24538
Joined: Mon Jan 14, 2008 12:52 pm
Location: Muskegon mich

Re: Brakes; getting closer. Opinion on pads and more

#13

Post by CYBORG »

I have a couple of the clicker type. Have had them for many years, and have had them checked a couple of times. They have not lost calabration over time. But I do keep them in the cases, and at the lowest setting when not in use
1978 custom GL1000
1977 custom with 1200 engine
1985 gl1200
User avatar
ianstaley
Titanium Member
Titanium Member
Posts: 486
Joined: Tue May 21, 2013 6:21 pm
Location: United Kingdom

Re: Brakes; getting closer. Opinion on pads and more

#14

Post by ianstaley »

Brake pad choice is something very personal but which brake pad and why? I found this which makes for good reading and may influence your choice.

go here for the article make good quick reading. http://www.ebay.co.uk/gds/Which-Brake-P ... 378/g.html

Ian
User avatar
bonestock3
Chrome Member
Chrome Member
Posts: 155
Joined: Wed Jan 21, 2015 5:47 pm
Location: Bronx, NY
Contact:

Re: Brakes; getting closer. Opinion on pads and more

#15

Post by bonestock3 »

ianstaley wrote:Brake pad choice is something very personal but which brake pad and why? I found this which makes for good reading and may influence your choice.

go here for the article make good quick reading. http://www.ebay.co.uk/gds/Which-Brake-P ... 378/g.html

Ian
* thanks Was certainly an enlightening read, it seems Kevlar isn't the best option for every day use. Fondly appreciate ur sharing.
robin1731 wrote:
If it is the "clicker" type you should also set it to the lowest setting after you are finished using it. Don't put it back in the tool box with it still set to 80lbs-ft. (that's just a number I pulled from the air)

If it came in a case use it. Torque wrench's are fairly delicate and calibrated instruments. Some of the cost a lot of money. Take good care of it. Some say they should be recalibrated every few years.
*it certainly is the clicker type. So store at lowest setting. Easy. Where would I take it to get recalibrated? What might cause them to lose calibration?
I like keeping it in the case like some magic wand.
.
Bonestock©
1979 GL1000 - Avomew
Post Reply
  • Similar Topics
    Replies
    Views
    Last post

Return to “GoldWing Tech Discussions”